by Dan Gonzalez

You’ve done it, you’ve bought your first DAW (Digital Audio Workstation)! This purchase is an exciting new chapter in your musical career. Now you can start recording your band practices, making demos, writing music, performing with a virtual band, etc. This purchase also comes with a whole new set of terms to learn. That’s why we created this FAQ - to make sure you’re equipped with the knowledge needed to get going in Music Creator fast.

• How do I record audio in Music Creator?
• What is an audio interface?
• What is a sound card?
• Do I need an audio interface?
• Can I just use my computer as an audio interface?
• What is the ASIO Driver Mode?
• How do I use the Metronome?
• What is a Dropout?
• Music Creator crashed, what do I do?
• What is mixing latency?
• What is recording latency?
• Why do I hear garbled audio or pops and clicks when I hit play?
• What is an audio input?
• What is a bus?
• What is an audio output?
• What is a send?
• What does Phantom Power(+48v) mean?
• How do I make an audio file?
• What is the difference between a .wav file and an .mp3 file?
• How do I make sound in Music Creator?
• Why doesn't MIDI make any sound?
• What is MIDI?
• I downloaded MIDI sequences from the internet, how do I get them into Music Creator?
• How do I use MIDI sequences or loop packs that came with Music Creator?
• How do I use a software instrument (VSTi) with my MIDI controller?

AUDIO

HOW DO I RECORD AUDIO IN MUSIC CREATOR?

1. On the File menu, click New.
2. Select the BASIC* template and click OK.
3. Click the first audio track to show its corresponding controls in the Inspector.
   • At the bottom of the inspector, you will see the track's input and output drop-down menus.
4. Click the Input drop-down menu to select the track’s input.
5. Select the physical jack that your instrument is plugged into. If you know, for instance, that your guitar is plugged into input 1, click the Input and select the first option. 
   • * Note: Most microphones and guitars are mono, so you'll want to select either the left or right channel accordingly.
6. Click the Output drop-down menu to select the track’s output.
7. Select the output that you want the audio track to play through during playback. You will usually choose 1 and 2, because these are most commonly the outputs that speakers or audio monitors are connected to.
8. Next, arm the track for recording. Make sure the track has been record enabled by clicking the track's Record Enable button . 
9. Click the Input Echo button  if you want to hear the input during recording. Many sound cards and audio interfaces have an option to do this automatically at the hardware level. If you can already hear the input signal, simply move on to the next section.
10. On the Transport in the Control Bar, click Record , or press [R] on your computer keyboard.
11. You'll hear two measures counted in by the metronome and then recording will begin. Start performing at the beginning of the third count.
12. When you finish recording, click the Stop button  or press the SPACEBAR.

WHAT IS AN AUDIO INTERFACE?

• This is an external piece of audio hardware that connects you to Music Creator. You can listen to your projects with studio headphones, record instruments with microphones, plugin your guitar, or just play audio loops. These connect to your computer with a USB cable, FireWire cable, Thunderbolt cable, or even an Ethernet cable.

WHAT IS A SOUND CARD?

• This is a piece of audio hardware that connects you to Music Creator. Sometimes the terms audio interface and sound card are used interchangeably. Specifying a device as a sound card typically means that the device is installed inside of a computer tower and connected directly to your computer’s motherboard.

DO I NEED AN AUDIO INTERFACE?

• Yes, always use an audio interface. They are inexpensive and will improve Music Creator’s performance.

CAN I JUST USE MY COMPUTER AS AN AUDIO INTERFACE?

• We strongly recommend against depending on your computer as your main audio interface. Most computers come with a headphone jack for watching videos on the internet or listening to music. Recording and mixing are not taken into account when manufacturers design computer audio ports.

WHAT IS THE ASIO DRIVER MODE?

• ASIO stands for Audio Stream Input/Output and was developed by Steinberg. It lets your audio interface or soundcard have access to multiple channels of streaming audio. Setting Music Creator to this mode allows Music Creator your audio interface to easily play more than just a stereo audio file simultaneously.
• You can set Music Creator to ASIO mode by going to Edit > Preferences > Audio > Playback and Recording | Driver Mode

HOW DO I USE THE METRONOME?

To set the tempo and metronome for a new project

1. In the Control Bar’s Transport, click the Playback Metronome on/off button  and Record Metronome on/off button  .
2. Right-click the Playback Metronome on/off button  or Record Metronome on/off button  to show metronome settings.
3. If you want to hear a count-in before recording begins, set the count-in to 1 or more. Select either Measures or Beats for the count-in.
4. Select Use Audio Metronome or Use MIDI Metronome.
5. Arm at least one track.
6. Press R or click  to start recording. The count-in will play, and the Now time will start to advance.
7. If necessary, stop playback and adjust the tempo using the tempo control in the Transport module, the restart playback. Repeat until the metronome plays the desired tempo.
8. Press the SPACEBAR or click  to stop recording.
9. Press W, or click  to rewind to the beginning of the piece.

Your tempo and metronome settings are now ready. When you save the project file, the metronome and tempo settings will be saved as well.

Check out more information about the metronome feature here.

WHAT IS A DROPOUT?

• The term "Dropout" is sometimes used interchangeably to describe a few different behaviors. Technically a dropout is when samples are dropped during playback and/or recording resulting in playback stopping.

Check out this article on article for a more in depth look at Dropouts.

MUSIC CREATOR CRASHED, WHAT DO I DO?

There may be a plug-in that is causing the project to crash. Try opening the project in Safe Mode:

1. Go to File > Open and select the project that crashes, but do not open it yet.
2. Hold down the SHIFT key and click Open.
3. The File Open - Safe Mode dialog box appears, prompting you to load the plug-ins that are used in the project.
4. Click No for any plug-in that has been recently installed or added to the project. You can also remove any non-Cakewalk plug-ins to ensure the project will load properly.

For more help on this subject, check out Cakewalk’s support portal here. 

WHAT IS MIXING LATENCY?

• Music Creator has a Buffer Size slider in Edit > Preferences > Audio - Driver Settings to set mixing latency. Mixing latency is the amount of time your DAW allocates to prepare a buffer full of audio data for playback. Lower latency settings add processing time because of the need to refill the smaller data buffers more often.
• You may need to use the slider to increase mixing latency under the following conditions.
  • You use lots of real-time effects, and you hear dropouts. Check the CPU meter for high readings; try increasing the latency.
  • Your sound card does not function well at lower latency. Some sound cards just do not function well at lower latency settings. Even though Music Creator’s CPU meter and Dropout indicator report no problems, if you hear dropouts try increasing the mixing latency.

WHAT IS RECORDING LATENCY?

• Recording Latency refers to a short period of delay (usually measured in milliseconds) between when an audio signal enters and when it emerges from a system. This is typically due to the analog-to-digital conversion and then the digital-to-analog conversion that comes back to the listener.

You can find out more about recording latency here.

WHY DO I HEAR GARBLED AUDIO OR POPS AND CLICKS WHEN I HIT PLAY?

• The most common reason why you have garbled playback or pops and clicks is because your Mixing Latency is set too low. See WHAT IS MIXING LATENCY? above to see how to adjust that.

WHAT IS AN AUDIO INPUT?

• Inputs receive audio signals from a source. Microphone inputs receive the audio signal from a microphone. 

WHAT IS A BUS?

• Buses are useful for mixing together different audio tracks (in stereo) and applying effects to the mix. You can mix the tracks at different volume levels by adjusting each track’s bus send level. Buses output to either other buses or to a main out.

You can find out more information about Buses here.

WHAT IS AN AUDIO OUTPUT?

• Outputs are the opposite of inputs. These expel data or audio. The output of a guitar plugs into the input of a guitar amp. 

WHAT IS A SEND?

• A Send is an output on your channel strip that can be used to route audio to another destination in your DAW.

WHAT DOES PHANTOM POWER (+48V) MEAN?

• Condenser microphones require a power supply of 48v. Just about any microphone input has an option for this. This can be damaging to ribbon microphones so make sure you understand the type of microphone you are using before even thinking about turning on Phantom Power.
• If your microphone requires Phantom Power then makes sure that you enable it or else you will not hear any sound at all.

HOW DO I MAKE AN AUDIO FILE?

To export audio to Wave file format:

1. Set all volume, pan, effects, and automation settings just as you want them.
2. If you only want to mix down parts of tracks, select those clips now. If you don’t select anything, everything is selected.
3. If you are using effects on the tracks and want to mix the effects down at this time, select the whole length of the longest track or clip plus extra time for the reverb or effects “tail.”
4. Choose File > Export > Audio to open the Export Audio dialog box.
5. Select a destination folder using the Look In field. (Unless you choose Share with Soundcloud, or YouTube)
6. Enter a file name.
7. Choose one of the following from the Export Preset drop-down list:
   • CD Quality. Choose this if you want to export a standard wave file.
   • DVD Quality. Choose this if you want to create an audio files optimized for DVD.
   • FLAC. Choose this if you want to create an audio file that is high-quality, yet small enough to add as an attachment to an email.
   • MP3. Choose this if you want an audio file that small in size. Unfortunately this audio file format slightly degrades the quality of your audio file.
   • Share with Soundcloud FLAC, MP3, WAV. Choose this if you would like to upload this directly to your SoundCloud account
   • Windows Media. Choose this if you would like to export to an audio file that is optimized for Windows Media Player
   • YouTube. Choose this if you would like to upload your music directly to your YouTube account.
8. Click Export.

WHAT'S THE DIFFERENCE BETWEEN A .WAV FILE AND AN .MP3 FILE?

• The reason why .mp3 files are so widely used is because of the convenient size. This format reduces large audio files into sizes that can fit as an attachment in most emails. Unfortunately this comes at the price of slightly degrading the sound quality.
• Wave files are uncompressed files and are a much larger size than the .mp3 format. Physical CDs use the Wave format.

MIDI

HOW DO I MAKE SOUND IN MUSIC CREATOR?

Add an Instrument Track in Music Creator and use the Onscreen Keyboard to play that instrument.

• Click on the Insert Synth button in the Synth Rack.
• Go to Insert Synths > Cakewalk Sound Center.
• If the Insert Synth Options dialog box appears, click OK.
• Go to Views > Virtual Controller/Keyboard. The virtual onscreen keyboard should appear.
• To play the synth with your computer keyboard hit the CAPS key.

Learn more about how to insert instruments in Music Creator here.

WHY DOESN'T MIDI MAKE ANY SOUND?

• MIDI is data, and is not audible by itself. You need to use a software instrument or hardware instruments to use MIDI to make sound.
• Music Creator opens MIDI files and routes them to an internal synthesizer for sound. If you modify the MIDI file then Music Creator will give you the option to save the project as a .cwp file for later modification. If you choose to not save the changes, the app will revert back to the original MIDI file unharmed or modified.

WHAT IS MIDI?

• MIDI is only performance data (which notes were played, their duration, how fast each note was pressed, etc.), and is not audible by itself. This data is used to trigger sounds from software or hardware based instruments that accept MIDI. It has been implemented for other uses too like control surfaces and synchronization. MIDI can travel over USB, MIDI Din, or Ethernet cables.

I DOWNLOADED MIDI SEQUENCES FROM THE INTERNET, HOW DO I GET THEM INTO MUSIC CREATOR?

One of the following will open your MIDI sequences in Music Creator.

• Double-click on the .mid file and it will open within your Music Creator.
• With the app open, drag and drop the .mid file right into it. 
• Inside of Music Creator, go to File > Import > Import MIDI and locate your .mid file

HOW DO I USE THE MIDI SEQUENCES OR LOOP PACKS THAT CAME WITH MUSIC CREATOR?

• Loop Packs and other free content that come with Music Creator can be accessible through the Browser. This is like a file directory for your computer through your DAW.

Check out how to use the Media Browser here.

HOW DO I USE A SOFTWARE INSTRUMENT (VSTi) WITH MY MIDI CONTROLLER?

After you have installed the driver for the MIDI Controller, add an Instrument Track in Music Creator.

1. In the Browser, click the Synth tab  (the last tab in the Browser). This is the Synth Rack, where you add your software instruments.
2. Click on the Insert Synth button in the Synth Rack.
3. Go to Insert Synths > Cakewalk Sound Center.
4. If the Insert Synth Options dialog box appears, click OK.
5. Next, arm the track for recording. Make sure the track has been record enabled by clicking the track's Record Enable  button.
6. Hit the Record button  in the Transport to begin recording.